Anuncios Clasificados
Bienvenid@,
Traemos lo que quieras, en menos de 25 días hábiles.
TÉRMINOS Y CONDICIONES
------------------------------------------
- Fotos referenciales del producto, consulte no mas
- Despachamos a todo Chile con Starken o Mercado Envios
- Productos traidos de Estados Unidos, es probable que los productos electronicos trabajen en 110V y NO en 220V, podria usar un transformador, para mas informacion primero nos puedes preguntar todas las inquietudes que tengas.
IVLPHA Empuje para conectar tubo de 1/8" OD x 10-32 UNF rosca macho, codo macho neumático línea de agua de aire codo giratorio de 90 grados conectores de empuje rápido (paquete de 5)
IVLPHA Push to Connect Fitting 1/8" Tube OD x 10-32 UNF Male Thread, Pneumatic Male Elbow Air Water Line 90 Deg Swivel Elbow Quick Push in Connectors (Pack of 5)
COLOR: UNICO
MODELO: 02U10
MARCA: IVLPHA
TALLA: 10-32 UNF - 1/8" OD
-Quick installation, simple and flexible, space-saving. Even after installation, the direction of tubing can be changed freely.
-The release ring adopts the ellipse design to make it more convenient and labor-saving for disconnection. Stainless steel locking claw, never stuck, never rust.
-All taper threads are pre-coated with Teflon with fine seal performance. (It may needs extra Teflon tape when thread of equipment damaged before)
-Fit for icemaker, refrigerator, cold water filter, etc. Please do not apply for the tube joint with additional external load (bending, twist or pulling, e.g.: Trailer, Air Suspension).
-Pressure Range: 0~1.1Mpa(0-160psi), Negative Pressure: -100Kpa (-29.5 in.Hg), Pressure Proof Test: 3.0Mpa (435psi), Temperature Range: 0~60 (32~140), Applicable Tube: Nylon,Polyamide (PA) / Polyurethane (PU). Applicable Fluid: Air, Vacuum, Water.
Before use, it should make clear following pointsWarninga) Except air and water (only special type and custom-design, e.g.: icemaker, refrigerator, cold water filter), never attempt to use the tube joint other fluids.b) The tube joint application is prohibited where spark and fire might be occurred.c) The tube joint application is prohibited if water temperature is above 60 (140) because resin might be decomposed and damaged in water under a high temperature.d) The tube joint is not designed for application where there is static charge.e) Never apply tube joint with additional external load (bending, twist or pulling, e.g.: Trailer, Air Suspension),Cautions1) If you use other supplier tubing, the different tubing tolerance might case leakage or incorrect connection and disassembly. It must check if tubing OD is measured by Metric Size or Inch Size.2) Always check the end of tubing for a right angle cutting and check the external surface of tubing for any damage or scratch. Please refer to following instruction in connection of tubing. When you insert the air tubing into the joint, you will have two-step feeling. Section One is locking claw while Section Two is sealing ring. You must insert the tube into Section Two.Sleeve is used in tubing connection and disconnection. The sleeve is designed as an oval shape, which is convenient in assembly and disassembly. After connection of tube joint and tubing, always try to pull tubing and ensure its firm connection.3) Cautions during disassembly of tubing before disconnection of tubing, always check tubing internal pressure for zero.For disconnection of tubing, always press sleeve heavily and then pull out tubing. If sleeve is net pressed with enough force, it is hard to pull out tubing and external surface scratch might be resulted by locking claw, which is the cause of air leakage. B09W5GX8N3
Anuncios Clasificados